How to check whether your monitors daisy-chain
Daisy-chaining means connecting monitors to each other in a series — PC to the first monitor, first monitor to the second — instead of running a cable from the PC to every screen. It works only through DisplayPort Multi-Stream Transport (MST), and only when every link in the chain supports it. This checker walks the four gates one by one: the operating system, the source port, the GPU, and the monitors themselves — then does the bandwidth maths.
To use it:
- Pick the operating system. macOS does not support MST at all, so a Mac cannot daisy-chain — the verdict is decided before any bandwidth maths. Windows supports MST natively; Linux supports it on most distributions with the amdgpu or i915 drivers.
- Pick the source port. The DisplayPort version decides the bandwidth budget: 17.3 Gbps usable on DP 1.2, 25.9 Gbps on DP 1.4, 38.7 on UHBR10, 52.2 on UHBR13.5 and 77.4 on UHBR20. A USB-C port with DisplayPort Alt Mode or a Thunderbolt port carries a DP 1.4 link. HDMI cannot daisy-chain at all.
- Check the GPU. Most desktop GPUs support MST from DisplayPort 1.2 on, but some laptop outputs and older cards do not expose it. Look for “MST” or “Multi-Stream Transport” on the GPU or laptop spec page.
- Describe each monitor. Resolution, refresh rate and colour depth decide how much bandwidth it needs — refresh rate is the biggest lever. Every monitor except the last also needs a DisplayPort output (labelled “DP Out”) and MST support, or the chain stops there.
- Check DSC. Display Stream Compression divides the bandwidth a monitor needs by about 2.5, and it can turn a “limited” into a “works” — but both the GPU and the monitor must support it.
- Read the verdict, then the bandwidth table. The table shows what each monitor needs and what the link carries, so you can see exactly which screen is eating the budget — and whether dropping 144 Hz to 60 Hz fixes it.
What makes this checker different
The pages that rank for this search are guides — thorough, but they explain the theory and leave you to work out what it means for the monitors on your desk. One rival site has a bandwidth calculator for a single resolution, but nothing answers the actual question: will these monitors, on this port, on this operating system, daisy-chain? This page is that answer: the operating-system gate, the HDMI gate, the GPU gate, the DP Out gate for every middle monitor, and the bandwidth maths for the whole chain — with the limiting factor named and the fix for each one. It is a self-assessment, so it says plainly what it cannot know: a web page cannot read the ports or the monitors, so anything you mark “Not sure” stays on the list until you confirm it on the device or the spec sheet.
When is this the right check?
Before you buy a second or third monitor to chain off the first: check the DP Out port and the bandwidth before the money moves. When a second monitor shows no signal in a chain you already wired: the checker names the cause — MST switched off, a missing DP Out port, bandwidth, or macOS — instead of leaving you to swap cables at random. When you are choosing between chaining and a dock: an MST hub splits the same link, so it never adds bandwidth — the checker shows whether the hub would help at all. And when a listing claims a monitor “daisy-chains”: run the exact resolution and refresh rate you want, not the headline spec, because a 4K 144 Hz chain fails where a 4K 60 Hz chain works.
Honest limitations
A self-assessment, not a test
This checker works only from the answers you enter. It cannot read the ports, the DisplayPort version, or whether a monitor implements MST — no web page can. If an answer is wrong, the verdict is wrong. Confirm the exact models on the manufacturers’ spec pages before buying cables.
The maths is an estimate
Each monitor’s bandwidth is estimated from its resolution, refresh rate and colour depth with a 25% allowance for blanking and protocol overhead, and DSC is counted at a conservative 2.5:1. Some monitors cap lower than the link allows — the monitor manual’s own daisy-chain table is the final word.
An MST hub adds no bandwidth
A hub replaces the monitors’ built-in DP Out ports — it does not add a second link. If the chain fails on bandwidth, a hub will not fix it: only a lower resolution, a lower refresh rate, DSC, or a second GPU output will.
macOS is a hard no
macOS does not support DisplayPort MST, so a Mac cannot drive two different displays from one DisplayPort link. No cable, hub or setting changes that — each monitor needs its own port or a Thunderbolt dock with a separate output per monitor.
HDMI ends the chain
HDMI carries one display stream. A monitor with only HDMI inputs cannot be chained from, and converting a DisplayPort chain to HDMI at the end of it ends the chain there. The chain has to stay DisplayPort all the way down.
Rules from VESA, dated November 2026
The rules here follow the published DisplayPort specifications and manufacturer daisy-chain guides as they read in November 2026: MST from DP 1.2, usable bandwidth 17.3 Gbps (HBR2), 25.9 Gbps (HBR3), 38.7 / 52.2 / 77.4 Gbps (UHBR10 / 13.5 / 20), and DSC at about 2.5:1 conservative. Newer ports and monitors may change the numbers, so re-check the spec pages if a new model appears.