Is it safe to drill into this wall — or is there a live cable behind it?

Cables are allowed to run straight up from every socket, along the top of the wall and down every corner — and a detector that finds nothing has not proved the wall is clear. Answer eight questions and this checker gives you the verdict for your exact spot — free, in your browser, nothing uploads.

  • UK, US, Canadian, Australian and EU rules
  • 150mm cable zones, checked
  • Detector limits stated honestly
  • Free, no account, nothing uploads

Check your drilling spot

Try a preset:

Your result

Answer the questions Your verdict appears here as you answer.
Rules that apply to your wall

Pick the country and the wall type above and the rules that apply will appear here.

Blockers

Fix first

Things to check

Still to confirm

What to do next

    Your result summary

    
              

    Answer the questions above — the verdict updates live.

    Privacy you can verify, not just trust

    Checking whether it is safe to drill into your wall by uploading photos of your home to a website would be backwards — the check should never be the leak. This one can't: your answers are checked with plain JavaScript on your device, and they never leave the device — the only third-party requests are the site's own analytics, which count page views. Don't take our word for it:

    New cross-origin requests during use: 0
    1. Press F12 to open developer tools, then the Network tab.
    2. Answer a question above. Watch: apart from the site's analytics, nothing new is requested — no uploads, and no data ever leaves your device.
    3. Extra credit: disconnect your internet after this page loads — the checker still works.

    How the safe-to-drill rule works

    There is no single answer to “is it safe to drill into this wall” — the answer is written by where the spot sits relative to the cable zones, and by what a detector has actually proved, in that order. The shape is the same across every guide that ranks for this search: cables are allowed to run straight up, straight down and straight across from every socket, switch and light fitting, and within 150mm of the ceiling and of every corner. A spot inside any of those strips is a no-drill spot, whatever a detector says. A spot outside them still needs a detector scan, because a detector that finds nothing has not proved the wall is clear — it has only proved it cannot see anything, and plastic pipes and switched-off cables are both invisible to it. The two checks together — outside the zones, and scanned clear — are what make a spot safe to drill.

    To use it:

    1. Pick the country. The UK, US, Canada, Australia and the EU all use prescribed cable zones, but the exact distances differ — the UK zones are 150mm, the US rule keeps cables 1-1/4 inches back from the framing edge. If you are not sure, the checker applies the strictest common reading (the UK 150mm zones) and says so.
    2. Work out the wall type. Knock on it: hollow means plasterboard on studs, solid means masonry. The wall type changes which detector works — a stud finder reads the adhesive dabs on a dot-and-dab wall, not framing, and a standard detector struggles at depth in concrete.
    3. Measure the two distances. How close is the spot to the nearest socket, switch or light fitting — and how close to the ceiling or a corner? These two answers are the zone test, and without them there is no verdict: a guess here is the one mistake that matters.
    4. Scan the spot. Use a detector with a live-cable mode (or a multi-detector), scan slowly, twice, from both directions, with the power on — a switched-off cable is invisible to the detector. If it beeps, move the spot at least 150mm away and scan again.
    5. Check the fixtures. Pipes run to every tap, shower, toilet and radiator, and plastic pipes are invisible to a standard detector. The worst spot of all is directly behind a toilet: the vent stack runs straight up the middle of that wall.
    6. Say how deep you will drill. A picture hook stays near the surface; a heavy fixing travels deep into the wall. Set a depth stop so the bit goes no deeper than the fixing needs, and start with a shallow pilot hole.

    What makes this checker different

    The pages that rank for this search are guides — BuildWiz, Solidex, GreenyPlace, Kwutah, Galaxus and a dozen DIY firms, each telling you the same rules in prose and leaving you to apply them to your own wall. There is no free, standalone checker that takes your country, your wall type, the two zone distances, your detector result, the fixtures on the wall, the room and the drilling depth, and gives you a verdict: safe to drill, drill with care, or do not drill here — with the blocker named, the detector corrected, and the next steps spelled out. The detector round-ups that do exist answer a different question (which device to buy), not whether your exact spot is safe. This page is that answer: eight questions, an instant verdict for your exact spot, the fixes named, and the next steps. It is a self-assessment, so it says plainly what it cannot know: a spot it cannot place outside the zones is reported as “can't tell”, not guessed — and a clear scan is never presented as a guarantee, because plastic pipes and dead cables are invisible to the detector.

    When is this the right check?

    Before you hang anything on a wall you have not drilled before — run the checker first, because the zone test takes thirty seconds and hitting a live cable takes far longer to fix. When the spot is anywhere near a socket, a switch, the ceiling or a corner, because those are the strips where cables are allowed to be. When the wall is in a bathroom or kitchen, because the pipework there is denser and mostly plastic. And whenever a guide gives you a flat “just use a stud finder” without mentioning the zones: this page applies the zone test first, and says so where the answer depends on a detector scan it has not yet seen.

    Honest limitations

    A self-assessment, not an electrician's judgement

    This checker cannot see inside your wall. It cannot feel a cable, hear a pipe, or know whether the wiring in your home follows the rules — so every safe verdict comes with the checks a detector cannot prove, and if anything feels wrong while you drill, stop and call a professional.

    Plastic pipes are invisible to a standard detector

    Modern homes use plastic push-fit pipes (PEX, HEP2O) for hot and cold water. A metal or live-cable detector that finds nothing proves nothing about plastic pipework — only a radar scanner sees it, and radar scanners start at about £260.

    A switched-off cable is invisible too

    Most consumer cable detectors only find live cables. Turn a circuit off at the consumer unit and that cable disappears from the detector. Test with the power on, then isolate the circuit before you drill.

    Old wiring may ignore the zones entirely

    The zones are the rule for properly wired homes. In an old home, or one with DIY wiring, cables can run diagonally — which is exactly what the rule exists to prevent. A clear scan and a spot outside the zones are both needed, not just one.

    The toilet vent stack is the hidden trap

    The plumbing vent stack is almost always centred directly behind the toilet — a 2-inch pipe running straight up the middle of that wall. Drilling above a toilet is likely to hit it, and no detector reading changes that.

    Rules from the guides, dated November 2026

    The rules here are the wiring and DIY guides' shared rules as they read in November 2026 — BuildWiz, Solidex, GreenyPlace, Kwutah, News Hub Central and HomeownersHub. Wiring regulations change: check your country's current edition before you start.

    Frequently asked questions

    Where should you never drill into a wall?

    Never drill directly above, below or beside a socket, switch or light fitting, and never within 150mm (6 inches) of the ceiling or a corner. Under the UK wiring rules (BS 7671), cables buried less than 50mm deep are allowed to run in exactly those routes — the prescribed zones — so those strips of wall are where live cables are expected to be. US rules say the same thing in different words: keep clear of the line of every outlet and switch, and keep cables at least 1-1/4 inches back from the edge of the framing.

    Can a stud finder tell me it is safe to drill?

    No. A stud finder locates framing, not cables — and a missing AC warning is not an all-clear. Shielded, inactive or deeply buried wiring may not trigger the warning at all, and a stud finder cannot see plastic water pipes. What you need is a detector with a live-cable mode (or a multi-detector), scanned slowly twice from both directions — and even then, only a radar scanner sees plastic pipes, and only a scan with the power on sees live cables, because a switched-off cable is invisible to the detector.

    What is a cable zone?

    A cable zone is a strip of wall where the wiring rules allow cables to run, so anyone fixing to the wall can predict where they are. Under BS 7671 the zones are: vertically and horizontally from any socket, switch or outlet; within 150mm of the top of the wall; and within 150mm of a corner. Cables buried less than 50mm deep must stay inside those zones and be protected by a 30mA RCD. A spot more than 150mm from the ceiling, more than 150mm from any corner, and not in line with any socket or switch should have no cables in a properly wired home — but old or amateur wiring can ignore the zones, which is why the checker still asks for a detector scan.

    Can I drill directly above a socket?

    No — directly above (or below, or beside) a socket is the single most common place people drill into a live cable, because cables are allowed to run straight up, straight down and straight across from every socket and switch. Move the spot at least 150mm (6 inches) away from the line of the accessory, then scan the new spot with a live-cable detector before drilling. The same applies above a light switch and beside a light fitting.

    What should I do if my detector beeps?

    Move the spot. A beep means something is behind the plaster here — a cable, a pipe or a stud — and drilling into it is the mistake this checker exists to prevent. Move at least 150mm (6 inches) away and scan again. If the detector beeps everywhere on the wall, stop and call an electrician: the services may be running somewhere unexpected. Note that a beep right next to an outlet is expected, not a fault — the cable is doing what the zones say it should.

    Can I drill into a wall in a bathroom?

    Only with extra care. Bathroom walls carry far more pipework than bedroom walls, and plastic pipes are invisible to a standard detector. The worst spot of all is directly above or behind the toilet: the plumbing vent stack is almost always centred behind it, a 2-inch pipe running straight up the middle of that wall. Trace every pipe route from the visible fixture — pipes usually run straight up or down from taps, showers and radiators — and if you have access to the attic, look for where the vent pipe exits the roof before drilling anything on that wall.

    Does this checker tell me for certain?

    No. This checker is a self-assessment: it runs your answers against the wiring and DIY guides' shared rules as they read in November 2026, entirely in your browser with plain JavaScript, and nothing you enter leaves your device. A web page cannot see inside your wall, so the verdict always comes with the checks a detector cannot prove — plastic pipes are invisible to a standard detector, a switched-off cable is invisible too, and old or amateur wiring may ignore the prescribed zones. Scan with the power on, isolate the circuit before you drill, start with a shallow pilot hole, and if anything feels wrong while you drill, stop and call a professional. The only third-party requests are the site's own analytics, which count page views. You can verify it yourself with the network-request counter in the privacy section below the checker.